自动搅拌一体机钢板易碎问题_公司新闻_新闻资讯_自动搅拌一体车_自动搅拌一体机

站内搜索

新闻资讯

公司新闻行业动态

热点

自动上料平口搅拌机多种方量可供选择

2022-12-23

混凝土自动上料搅拌车的功能有哪些？

2022-12-19

混凝土自动拌料车移动式可自行走户外施工

2022-12-16

自上料搅拌车企业这么多，买车的时候应该看哪方面？

2022-12-12

关于山汽

联系人：刘老师

电话：400-879-1999

公司：山东山汽工程机械（集团）有限公司

地址：山东省莱州市206国道与308省道交叉口东南50米

自动搅拌一体机钢板易碎问题

所属分类：公司新闻发布时间：2020-06-18 来源：http://www.shanqijituan.cn/ 浏览量：0

自动搅拌一体机的前钢板由九块组成。许多人报告说，自动搅拌一体机的和第二部分在使用过程中容易破裂是什么原因？

The front steel plate of the automatic mixing and feeding machine is composed of nine pieces. Many people report that the first and second parts of the automatic mixing and feeding machine are easy to crack in use?

（1）过度使用紧急制动器。在山上行驶时，在下坡路上使用紧急制动器可能会损坏前板。由于制动力，自动搅拌上料机的大部分负荷质量得到前板簧的促进和接受。结果，可能发生片簧的疲劳损坏。建议使用排气制动器以减少紧急制动。

(1) Excessive use of emergency brake. When driving on a hill, using the emergency brake on a downhill road can damage the front panel. Because of the braking force, most of the load mass of the automatic mixing feeder is promoted and accepted by the front leaf spring. As a result, fatigue damage to the leaf spring may occur. The use of exhaust brakes is recommended to reduce emergency braking.

（2）前轮制动调整太紧。如果后轮制动性能不佳，或者发生突然问题，请使用紧急制动器并通过过度冲击破坏前板簧。

(2) Front wheel brake adjustment is too tight. If the brake performance of the rear wheels is poor or there is a sudden problem, use the emergency brake and destroy the front leaf spring through excessive impact.

（3）路面不好，超载，超速，对前板簧施加过大的冲击力，容易造成损坏。

(3) The road surface is not good, overload, overspeed, exert too much impact on the front leaf spring, easy to cause damage.

（4）前板簧经常长时间过载，降低弹性和刚性，并因疲劳而损坏。

(4) The front leaf spring is often overloaded for a long time, reducing elasticity and rigidity, and is damaged due to fatigue.

（5）更换低质量的板簧。刀片弯曲不符合标准。由于钢板材料不好或热处理不好，应力变得不均匀和断裂。

(5) Replace the low quality leaf spring. The blade is bent out of standard. Due to the bad material or heat treatment of steel plate, the stress becomes uneven and fracture.

为防止自动搅拌上料机前板簧的和第二块自动装载，我们建议采用以下方法：

In order to prevent the first and second automatic loading of the front leaf spring of the automatic mixing feeder, we recommend the following methods:

（1）检查时间，确保板簧良好润滑，并正确调整车辆制动器。

(1) Check the time to make sure that the leaf springs are well lubricated and that the vehicle brakes are adjusted correctly.

（2）减少紧急制动器的使用，增加发动机排气制动器的使用，均匀地施加载荷而不会过载。

(2) Reduce the use of emergency brake, increase the use of engine exhaust brake, evenly apply load without overload.

（3）更换前钢板时，必须使用钢板，以确保弯曲度符合要求。使用山东弹簧厂和重庆弹簧厂生产的板簧。

(3) When replacing the front steel plate, high-quality steel plate must be used to ensure that the bending degree meets the requirements. It is better to use the leaf spring produced by Shandong spring factory and Chongqing Spring Factory.

（4）在不平坦的道路上行驶或下坡行驶时，需要控制自动搅拌上料机的速度并在曲线上行驶。不要急于过快。

(4) When driving on uneven road or downhill, it is necessary to control the speed of the automatic mixing feeder and drive on the curve. Don't rush too fast.

自动搅拌上料机传动油品质检测方法

Quality inspection method for transmission oil of automatic mixing and feeding machine

1.将自动搅拌机放在平坦的表面上并拧紧手制动器。

1. Place the automatic mixing feeder on a flat surface and tighten the hand brake.

2.让发动机空转几分钟。y

2. Allow the engine to idle for a few minutes.

3.踩下制动踏板并转动操纵杆前后移动。将每个齿轮移动几秒钟以填充变矩器和所有带液压油的换档执行器。，将操纵杆转到停车位置。

3. Press the brake pedal and turn the control lever to move forward and backward. Move each gear for a few seconds in order to fill the torque converter and all shift actuators with hydraulic oil. Finally, turn the lever to the park position.

4.从加注管上取下自动量油尺，将清洁的量油尺插入加油管并将其拉出以检查量油尺的油位。

4. Remove the automatic dipstick from the filler tube, insert the clean dipstick into the filler tube and pull it out to check the oil level of the dipstick.

在检查或排除自动搅拌一体机故障之前，检查变速箱油位和油质。换档杆必须处于P位置，发动机应在空转时运转少几分钟，液体将达到正常工作温度，并且车辆必须停在水平面上以确保差速器和节气门之间的油位。通常传输是稳定的。

Check the oil level and quality of the gearbox before checking or troubleshooting the automatic mixing feeder. The shift lever must be in the P position, the engine should be running at idle for at least a few minutes, the fluid will reach normal operating temperature, and the vehicle must be stopped on a level surface to ensure the oil level between the differential and the throttle. Transmission is usually stable.

自动搅拌一体机的钢板断裂和传动油质量检查问题介绍就是这样了，希望对你有帮助。

This is the introduction of steel plate fracture and transmission oil quality inspection of automatic mixing and feeding machine. I hope it can help you.

上一页：多功能搅拌车减震器怎么样保养？下一页：多功能搅拌车你真的了解吗？

热门产品 / HOT PRODUCT