自动搅拌一体车的轮胎多久更换一次？_公司新闻_新闻资讯_自动搅拌一体车_自动搅拌一体机

站内搜索

新闻资讯

公司新闻行业动态

热点

自动上料平口搅拌机多种方量可供选择

2022-12-23

混凝土自动上料搅拌车的功能有哪些？

2022-12-19

混凝土自动拌料车移动式可自行走户外施工

2022-12-16

自上料搅拌车企业这么多，买车的时候应该看哪方面？

2022-12-12

关于山汽

联系人：刘老师

电话：400-879-1999

公司：山东山汽工程机械（集团）有限公司

地址：山东省莱州市206国道与308省道交叉口东南50米

自动搅拌一体车的轮胎多久更换一次？

所属分类：公司新闻发布时间：2020-12-25 来源：http://www.shanqijituan.cn/ 浏览量：0

随着自动搅拌一体车的成本持续增加，轮胎价格也随之上涨。如果使用不当，会造成异常磨损。自动搅拌一体车的轮胎多久更换一次？让我们一起学习吧。

As the cost of automatic mixer truck continues to increase, tire prices also rise. If used improperly, it will cause abnormal wear. How often do the tires of all-in-one truck change? Let's study together.

1.轮胎胎面深度

1. Tire tread depth

胎面花纹的厚度必须大于1.6毫米。如果您驾驶的是低摩擦湿路面，请确保胎面花纹厚度是上述值的两倍。您可以购买量规中学习，以测量胎面花纹的厚度;然而，较老的驾驶员经常使用广泛传播的方法粗略估计胎面花纹的厚度，即花费一美元并跟随它。将胎面凹槽沿顶部方向插入，因为从边缘到顶部的距离在1到2毫米之间，因此此时整个胎面花纹的厚度不足。

The thickness of the tread pattern must be greater than 1.6 mm. If you are driving on a low friction wet road, make sure that the tread thickness is twice that. You can buy gauges to learn to measure the tread thickness; however, older drivers often use a widely spread method to roughly estimate the tread thickness, that is, to spend a dollar and follow it. Insert the tread groove in the top direction because the distance from the edge to the top is between 1 and 2 mm, so the thickness of the entire tread pattern is insufficient.

2.胎面花纹磨损指示线

2. Tread wear indicator line

新轮胎的设计比过去的老式产品更加用户友好：胎面花纹磨损指示器。当轮胎非常新或具有非常低的磨损水平时，这些指示器几乎不可察觉，但是当磨损达到一定水平时，隐藏在胎面冲沟中的这些线出现。胎面花纹磨损指示线是扁平橡胶条，其在胎面的纵向方向上垂直地嵌入胎面凹槽中。当您检查轮胎并偶尔找到一条或两条指示线时，胎面花纹的厚度已经减少了很多。在这种情况下，在湿滑的道路上行驶时应小心。如果轮胎上的几乎所有指示线都清晰可见，则需要尽快更换轮胎。

The design of the new tire is more user-friendly than the old one: tread wear indicator. These indicators are almost imperceptible when the tire is very new or has a very low wear level, but when the wear reaches a certain level, these lines hidden in the tread grooves appear. The tread pattern wear indicator line is a flat rubber strip, which is vertically embedded in the tread groove in the longitudinal direction of the tread. When you check the tire and occasionally find one or two indicator lines, the tread thickness has been reduced a lot. In this case, be careful when driving on slippery roads. If almost all the indicator lines on the tire are clearly visible, the tire needs to be replaced as soon as possible.

3.轮胎侧壁裂缝

3. Tire sidewall cracks

轮胎上的问题并非都集中在胎面上，并且轮胎的侧壁存在一些问题。寻找轮胎侧壁上肉眼可见的裂缝和切口。这些微小的凹槽表明轮胎可能在未来泄漏，更糟糕的是，轮胎爆裂。这些轮胎故障是我们想要避免的。因此，当轮胎的侧壁裂缝看起来更严重时，车辆被驱动到维修车间以快的速度更换轮胎。

Not all the problems on the tire are concentrated on the tread, and there are some problems on the sidewall of the tire. Look for visible cracks and cuts in the tire sidewall. These tiny grooves indicate that the tire may leak in the future and, worse, burst. These tire failures are what we want to avoid. As a result, when the sidewall cracks look more severe, the vehicle is driven to the workshop to change the tire as quickly as possible.

4.轮胎上的鼓胀和起泡

4. Bulging and blistering on tires

在一些情况下，由于强度不足，轮胎的外表面可能上升并在正常轮胎的表面上方起泡。轮胎也面临着类似的情况。如果您未能将车辆运送到维修店并注意到轮胎故障，则胎面强度不足的区域可能会突然高速爆裂。轮胎爆裂甚可能对驾驶员和乘客造成严重伤害。

In some cases, the outer surface of the tire may rise and blister over the surface of the normal tire due to insufficient strength. Tires face a similar situation. If you fail to deliver the vehicle to the repair shop and notice a tire failure, areas with insufficient tread strength may burst suddenly at high speed. A burst tire may even cause serious injury to the driver and passengers.

在车辆行驶期间不可避免地会出现一定量的抖动，尤其是在恶劣的道路条件下。当您有一定的驾驶体验时，您可以感觉到合理范围内的抖动以及抖动如何表明车辆出现故障。

It is inevitable that there will be a certain amount of jitter during the vehicle driving, especially under the bad road conditions. When you have a certain driving experience, you can feel the shaking within a reasonable range and how the shaking indicates that the vehicle is in trouble.

自动搅拌一体车的轮胎个更换问题介绍就是这样了，希望对你有帮助。

This is the first tire replacement problem of automatic mixing truck. I hope it can help you.

上一页：如何判断搅拌一体车方向盘是否回正？下一页：多功能搅拌车无需用电野外施工难题

热门产品 / HOT PRODUCT