欢迎光临山汽集团网站!

400-879-1999

点击拨打服务热线:400-879-1999
您现在所在的位置: 首页> 新闻资讯 > 公司新闻
站内搜索
关于山汽

联系人:刘老师

电话:400-879-1999

公司:山东山汽工程机械(集团)有限公司

地址:山东省莱州市206国道与308省道交叉口东南50米

自动搅拌一体车液压系统的维护

所属分类:公司新闻 发布时间:2020-06-08 来源:http://www.shanqijituan.cn/ 浏览量:0

在自动搅拌一体车运用过程中,假定液压体系呈现缺点会使搅拌车的作业功用大大下降,只需了解了液压体系的缺点原因并及时排出处理缺点才华使搅拌车康复正常,今日收集了有关搅拌车液压体系压力短少或完全无压力的原因、确诊和清扫,希望能帮到咱们。
In the application process of the automatic mixer, if the hydraulic system presents defects, the operation function of the mixer will be greatly reduced. Only by understanding the causes of the defects of the hydraulic system and timely handling the defects can the mixer recover normally. Today, we collected the causes, diagnosis and cleaning of the short or no pressure of the hydraulic system of the mixer, hoping to help us.
假定自动搅拌一体车呈现液压体系压力短少或完全无压力时,咱们能够依据以下几个方面顺次进行排查:
Assuming that the hydraulic system pressure of the automatic mixer is short or no pressure at all, we can check in sequence according to the following aspects:
查看液压泵是否能输出液压油。假定是新的液压泵,无液压油输出,可能是泵体有铸造缺点(缩孔、砂眼等),使吸油腔和压油腔相通,失掉压油才华,应及时找厂家替换。若不是新的液压泵,无液压油输出,则可能是泵的转向不对,零件磨损严峻或损坏,及时替换。
Check whether the hydraulic pump can output hydraulic oil. If it is a new hydraulic pump without hydraulic oil output, the pump body may have casting defects (shrinkage cavity, sand hole, etc.), so that the oil suction cavity is connected with the oil pressure cavity, and the oil pressure talent is lost, it should be replaced by the manufacturer in time. If it is not a new hydraulic pump and there is no hydraulic oil output, it may be that the steering of the pump is not correct, the parts are severely worn or damaged, and they shall be replaced in time.
若液压泵有油液输出,查看溢流阀作业是否正常。若不正常,则可能是压力油路的某几个阀有污物或其他原因卡住,处于回油方位,致使压力油路与溢流回路短路,也可能是管接头松脱,或处于压力油路中的某些阀走漏严峻,或液压缸、液压马达的密封损坏,严峻走漏。
自动搅拌一体车
If the hydraulic pump has oil output, check whether the overflow valve operates normally. If it is abnormal, it may be that some valves of the pressure oil circuit are stuck due to dirt or other reasons, which are in the oil return direction, resulting in a short circuit between the pressure oil circuit and the overflow circuit, or the pipe joint is loose, or some valves in the pressure oil circuit leak severely, or the seal of the hydraulic cylinder and hydraulic Marta is damaged, which leads to severe leakage.
清扫办法:拆开有关阀进行清洗,查看密封空位的巨细及各种密封设备,密封设备损坏应替换。
Cleaning method: disassemble relevant valves for cleaning, check the size of sealing space and various sealing equipment, and replace the damaged sealing equipment.
若液压泵输出流量随压力升高而明显减小,且压力达不到规定值,则是因为液压泵磨损后空位增大所构成的。
If the output flow of the hydraulic pump decreases obviously with the increase of the pressure, and the pressure can not reach the specified value, it is caused by the increase of the vacancy after the wear of the hydraulic pump.
清扫办法:测定液压泵的容积功率,即可供认该泵是否能持续运用,对磨损严峻的零件,应进行修配或替换。
Cleaning method: measure the volume power of the hydraulic pump to confirm whether the pump can be used continuously. Repair or replace the severely worn parts.
若整个自动搅拌一体车液压体系能树立正常压力,而某些管路或液压缸(或液压马达)中没有压力,就有可能是因为小孔、管路或许换向阀、节流阀等部位阻塞。此刻,应逐段查看压力和有无油液经过,找出原因,加以清扫。
If the hydraulic system of the whole automatic mixer can set up normal pressure, and there is no pressure in some pipelines or hydraulic cylinders (or hydraulic motors), it may be because of the blockage of small holes, pipelines or reversing valves, throttle valves and other parts. At this moment, it is necessary to check the pressure and oil flow section by section, find out the cause and clean it.
感谢您的阅读,此文的文章来源:在自动搅拌一体车运用过程中,假定液压体系呈现缺点会使搅拌车的作业功用大大下降,只需了解了液压体系的缺点原因并及时排出处理缺点才华使搅拌车康复正常,今日收集了有关搅拌车液压体系压力短少或完全无压力的原因、确诊和清扫,希望能帮到咱们。
In the application process of the automatic mixer, if the hydraulic system presents defects, the operation function of the mixer will be greatly reduced. Only by understanding the causes of the defects of the hydraulic system and timely handling the defects can the mixer recover normally. Today, we collected the causes, diagnosis and cleaning of the short or no pressure of the hydraulic system of the mixer, hoping to help us.
假定自动搅拌一体车呈现液压体系压力短少或完全无压力时,咱们能够依据以下几个方面顺次进行排查:
Assuming that the hydraulic system pressure of the automatic mixer is short or no pressure at all, we can check in sequence according to the following aspects:
查看液压泵是否能输出液压油。假定是新的液压泵,无液压油输出,可能是泵体有铸造缺点(缩孔、砂眼等),使吸油腔和压油腔相通,失掉压油才华,应及时找厂家替换。若不是新的液压泵,无液压油输出,则可能是泵的转向不对,零件磨损严峻或损坏,及时替换。
Check whether the hydraulic pump can output hydraulic oil. If it is a new hydraulic pump without hydraulic oil output, the pump body may have casting defects (shrinkage cavity, sand hole, etc.), so that the oil suction cavity is connected with the oil pressure cavity, and the oil pressure talent is lost, it should be replaced by the manufacturer in time. If it is not a new hydraulic pump and there is no hydraulic oil output, it may be that the steering of the pump is not correct, the parts are severely worn or damaged, and they shall be replaced in time.
若液压泵有油液输出,查看溢流阀作业是否正常。若不正常,则可能是压力油路的某几个阀有污物或其他原因卡住,处于回油方位,致使压力油路与溢流回路短路,也可能是管接头松脱,或处于压力油路中的某些阀走漏严峻,或液压缸、液压马达的密封损坏,严峻走漏。
If the hydraulic pump has oil output, check whether the overflow valve operates normally. If it is abnormal, it may be that some valves of the pressure oil circuit are stuck due to dirt or other reasons, which are in the oil return direction, resulting in a short circuit between the pressure oil circuit and the overflow circuit, or the pipe joint is loose, or some valves in the pressure oil circuit leak severely, or the seal of the hydraulic cylinder and hydraulic Marta is damaged, which leads to severe leakage.
清扫办法:拆开有关阀进行清洗,查看密封空位的巨细及各种密封设备,密封设备损坏应替换。
Cleaning method: disassemble relevant valves for cleaning, check the size of sealing space and various sealing equipment, and replace the damaged sealing equipment.
若液压泵输出流量随压力升高而明显减小,且压力达不到规定值,则是因为液压泵磨损后空位增大所构成的。
If the output flow of the hydraulic pump decreases obviously with the increase of the pressure, and the pressure can not reach the specified value, it is caused by the increase of the vacancy after the wear of the hydraulic pump.
清扫办法:测定液压泵的容积功率,即可供认该泵是否能持续运用,对磨损严峻的零件,应进行修配或替换。
Cleaning method: measure the volume power of the hydraulic pump to confirm whether the pump can be used continuously. Repair or replace the severely worn parts.
若整个自动搅拌一体车液压体系能树立正常压力,而某些管路或液压缸(或液压马达)中没有压力,就有可能是因为小孔、管路或许换向阀、节流阀等部位阻塞。此刻,应逐段查看压力和有无油液经过,找出原因,加以清扫。
If the hydraulic system of the whole automatic mixer can set up normal pressure, and there is no pressure in some pipelines or hydraulic cylinders (or hydraulic motors), it may be because of the blockage of small holes, pipelines or reversing valves, throttle valves and other parts. At this moment, it is necessary to check the pressure and oil flow section by section, find out the cause and clean it.
感谢您的阅读,此文的文章来源:自动搅拌一体车更多的内容和问题请点击:http://www.shanqijituan.cn我们会继续努力的为您提供服务,感谢您的支持!
Thank you for your reading. For more information and questions, please click: http://www.shanqijituan.cn We will continue to work hard to provide you with services, thank you for your support!更多的内容和问题请点击:http://www.shanqijituan.cn我们会继续努力的为您提供服务,感谢您的支持!
Thank you for your reading. For more information and questions, please click: http://www.shanqijituan.cn We will continue to work hard to provide you with services, thank you for your support!
热门产品 / HOT PRODUCT
4.0方自动搅拌一体车
产品

4.0方自动搅拌一体车

3.5方A款系列搅拌车
产品

3.5方A款系列搅拌车

2.6方同步旋转搅拌车
产品

2.6方同步旋转搅拌车

6.5方系列搅拌车
产品

6.5方系列搅拌车

0.5方搅拌车
产品

0.5方搅拌车

3.5方B款自动搅拌一体车
产品

3.5方B款自动搅拌一体车

5.5方多功能搅拌车
产品

5.5方多功能搅拌车

4方同步旋转搅拌车
产品

4方同步旋转搅拌车

4吨B后尾
产品

4吨B后尾

6.5方系列搅拌车
产品

6.5方系列搅拌车

4方同步旋转搅拌车
产品

4方同步旋转搅拌车

1.6方平口搅拌车
产品

1.6方平口搅拌车

倾翻上抓
产品

倾翻上抓

4.0方搅拌车多功能
产品

4.0方搅拌车多功能

1.8方搅拌一体车
产品

1.8方搅拌一体车

0.5方自动搅拌一体机
产品

0.5方自动搅拌一体机

2方平口搅拌车
产品

2方平口搅拌车

3.5方A款自动系列
产品

3.5方A款自动系列

4吨B斜前
产品

4吨B斜前

3.5方D款搅拌车
产品

3.5方D款搅拌车

4吨A后尾
产品

4吨A后尾

3.5方B款自动搅拌一体机
产品

3.5方B款自动搅拌一体机

1.2方系列搅拌车
产品

1.2方系列搅拌车

4方同步旋转自上料搅拌机
产品

4方同步旋转自上料搅拌机

1.8方平口搅拌车
产品

1.8方平口搅拌车

3.5吨A正侧
产品

3.5吨A正侧

3.5方C款搅拌车
产品

3.5方C款搅拌车

2方后置驾驶室自动搅拌一体车
产品

2方后置驾驶室自动搅拌一体车

3.5吨B款后尾
产品

3.5吨B款后尾

5.5方自动搅拌一体车
产品

5.5方自动搅拌一体车

2.6方自动搅拌一体车
产品

2.6方自动搅拌一体车

5.5方自动搅拌一体机
产品

5.5方自动搅拌一体机

3.5方C款自动搅拌一体机
产品

3.5方C款自动搅拌一体机

3.5吨B款斜前
产品

3.5吨B款斜前

4方平口搅拌车
产品

4方平口搅拌车

1.5方平口搅拌车
产品

1.5方平口搅拌车

3.5方D款自上料搅拌机
产品

3.5方D款自上料搅拌机

2方后置驾驶室自动搅拌一体机
产品

2方后置驾驶室自动搅拌一体机

4.0方自上料搅拌机
产品

4.0方自上料搅拌机

3.5吨C正侧
产品

3.5吨C正侧

铲斗外翻
产品

铲斗外翻

3.5吨C斜前
产品

3.5吨C斜前

1.2方平口搅拌车
产品

1.2方平口搅拌车

4吨A后侧
产品

4吨A后侧

5.5方平口搅拌车
产品

5.5方平口搅拌车

3.5吨C后侧
产品

3.5吨C后侧

2.6方同步旋转多功能搅拌车
产品

2.6方同步旋转多功能搅拌车

2方后置驾驶室多功能搅拌车
产品

2方后置驾驶室多功能搅拌车

铲斗内收
产品

铲斗内收

4吨C后侧
产品

4吨C后侧

4吨A正侧
产品

4吨A正侧

3.5吨A后尾
产品

3.5吨A后尾

3.5吨A斜前
产品

3.5吨A斜前

2.6方自动搅拌一体机
产品

2.6方自动搅拌一体机

3.5吨C后尾
产品

3.5吨C后尾

超宽1.8米挡货架
产品

超宽1.8米挡货架

2.6方搅拌车
产品

2.6方搅拌车

4吨B正侧
产品

4吨B正侧

4方同步旋转自动搅拌一体机
产品

4方同步旋转自动搅拌一体机

倾翻上抓
产品

倾翻上抓

4吨A斜前
产品

4吨A斜前

3.5方C款自上料搅拌机
产品

3.5方C款自上料搅拌机

1.2方自动搅拌一体机
产品

1.2方自动搅拌一体机

倾翻上抓
产品

倾翻上抓

3.5方平头搅拌车
产品

3.5方平头搅拌车

3.5吨地下室正侧
产品

3.5吨地下室正侧

3.5吨地下室后尾
产品

3.5吨地下室后尾

3.5方多功能搅拌一体车
产品

3.5方多功能搅拌一体车

6.5方自动搅拌一体机
产品

6.5方自动搅拌一体机

3.5方D款搅拌车系列
产品

3.5方D款搅拌车系列

4吨C正侧
产品

4吨C正侧

棉花叉
产品

棉花叉

4吨C后尾
产品

4吨C后尾

6.5方自上料搅拌机
产品

6.5方自上料搅拌机

4吨B后侧
产品

4吨B后侧

下倾翻
产品

下倾翻

3.5方C款搅拌一体车
产品

3.5方C款搅拌一体车

2.6方平口搅拌车
产品

2.6方平口搅拌车

3.5吨地下室后侧
产品

3.5吨地下室后侧

3.5吨A后侧
产品

3.5吨A后侧

抓木器图片
产品

抓木器图片

2方平口搅拌车
产品

2方平口搅拌车

3.5方平口搅拌车
产品

3.5方平口搅拌车

1.2方自动搅拌一体车
产品

1.2方自动搅拌一体车

1.8方多功能搅拌车
产品

1.8方多功能搅拌车

3.5方A款自动搅拌一体机
产品

3.5方A款自动搅拌一体机

5.5方自上料搅拌机
产品

5.5方自上料搅拌机

1.8方自动搅拌一体机
产品

1.8方自动搅拌一体机

3.5吨B款正侧
产品

3.5吨B款正侧

4.0方自动搅拌一体机
产品

4.0方自动搅拌一体机

3.5吨地下室斜前
产品

3.5吨地下室斜前

4吨C斜前
产品

4吨C斜前

3.5方D款自动搅拌一体机
产品

3.5方D款自动搅拌一体机

3.5方B款自上料搅拌机
产品

3.5方B款自上料搅拌机

3.5吨A正侧
产品

3.5吨A正侧

3.5方A款自上料搅拌机
产品

3.5方A款自上料搅拌机

0.5方一体车系列
产品

0.5方一体车系列

2.6同步旋转方自动搅拌一体机
产品

2.6同步旋转方自动搅拌一体机

2方后置驾驶室自上料搅拌机
产品

2方后置驾驶室自上料搅拌机

新闻 / NEWS RECOMMEND ATIONS
首页 产品 电话 置顶