怎么恢复多功能搅拌车的驱动使用？ - 公司新闻_新闻资讯-山东山汽工程机械(集团)有限公司

站内搜索

新闻资讯

公司新闻行业动态

热点推荐

自动上料平口搅拌机多种方量可供选择

2022-12-23

混凝土自动上料搅拌车的功能有哪些？

2022-12-19

混凝土自动拌料车移动式可自行走户外施工

2022-12-16

自上料搅拌车品牌这么多，买车的时候应该看哪方面？

2022-12-12

关于山汽

联系人：刘老师

电话：400-879-1999

公司：山东山汽工程机械（集团）有限公司

地址：山东省莱州市206国道与308省道交叉口东南50米

怎么恢复多功能搅拌车的驱动使用？

所属分类：公司新闻发布时间：2021-03-12 来源：http://www.shanqijituan.cn/ 浏览量：18

多功能搅拌车大多数的拌和操作均系机械拌和，以中、低压立式钢制容器的拌和设备为主，来了解下拌和时机呈现什么问题：

Most of the mixing operations of multi-functional mixer are mechanical mixing, mainly the mixing equipment of medium and low pressure vertical steel containers

紧迫驱动结束后,将驱动软管卸下,并康复两车原状。将多功能搅拌车熄火,将其液压马达的高压油管卸下,并与毛病车上的对应接头用紧迫驱动软管相在托轮和滚道之间放入木楔,以操控拌和筒的旋转。

After the end of the emergency drive, remove the drive hose and recover the two vehicles. Turn off the multi-function mixer, remove the high-pressure oil pipe of its hydraulic motor, and connect it with the corresponding joint on the defective truck with an urgent driving hose. Put a wedge between the supporting wheel and the raceway to control the rotation of the mixing drum.

必定要留意安全;将发起机熄火，拆松液压马达的一根高压油管,拌和筒可自由旋转，操控拌和筒的旋转,使修理孔转到下部,然后打开修理孔，整理出筒内混凝土,此时必定要留意安全,混凝土排出结束后，康复拌和车原状。发起拌和车,将其操作手柄拨至出料方位,毛病车内的混凝土即被排出。准备好紧迫驱动软管,将拌和车熄火,卸下液压马达上的高压油管接头。

Be sure to pay attention to safety; turn off the engine, remove a high-pressure oil pipe of the hydraulic motor, and the mixing drum can rotate freely. Control the rotation of the mixing drum to turn the repair hole to the lower part, and then open the repair hole to sort out the concrete in the drum. At this time, be sure to pay attention to safety, and recover the original state of the mixing truck after the concrete is discharged. Start the mixing truck, turn its operating handle to the discharging position, and the concrete in the defective truck will be discharged. Prepare the emergency drive hose, turn off the mixer, and remove the high-pressure oil pipe connector on the hydraulic motor.

多功能搅拌车在上料时有什么要求，假如在进料期间呈现堵料的状况要怎样处理，提早如何备料才会相对来说好些，能尽量防止详细来看下吧：

What are the requirements of the multi-function mixer when loading? If there is a material blockage during the feeding period, how to deal with it, and how to prepare the material in advance will be relatively better

有时候咱们会使用手动料枪吸料，为了方便操作直接将料枪刺进物料桶或许吨袋中，料枪吸料口被严实的物料压缩，强大的负压将满满的物料拉走，这对上料机损伤非常大，且极易阻塞管道。

Sometimes we use the manual material gun to suck the material. In order to facilitate the operation, we directly stab the material gun into the material barrel or the ton bag. The suction port of the material gun is compressed by the solid material, and the strong negative pressure pulls the full material away. This is very harmful to the feeder, and it is very easy to block the pipe.

正确的方式是物料在吸料口和空气构成必定的气物混合比，在气流的推进下均匀流入上料机。这个时候咱们需要将料枪规划带有补气功能。假如物料积压时间过长或许很硬，这个时候需要在料枪上装一个振荡器，敲碎结块的物料。

The correct way is that the material in the suction port and the air constitute a certain air-material mixture ratio, and flow into the feeder evenly under the promotion of air flow. At this time, we need to plan the material gun with air supply function. If the material overstock time is too long, it may be very hard. At this time, we need to install an oscillator on the material gun to break the caked material.

上一页：自动搅拌一体车的关键机械部件检查方法有哪些？下一页：自动搅拌一体机户外工作底盘损伤紧急修复方法?

热门产品 / HOT PRODUCT