今天我们小编就来给您介绍自动上料搅拌车的保养注意事项,希望通过我们的介绍让您对自动上料搅拌车的保养注意事项等问题有更深入的了解
Today, our editor will introduce you to the maintenance precautions of automatic feeding mixer truck. We hope that through our introduction, you can have a deeper understanding of the maintenance precautions of automatic feeding mixer truck and other issues
1、在施工现场卸料完毕后,应立即用搅拌车随带的软管冲洗进料斗、出料斗、卸料熘槽等处,清理粘附在车身各处的污泥及混凝土。在返回搅拌站的途中,应向搅拌筒内注150---200L水以清洗筒壁及叶片粘结的混凝土残渣。
1. After unloading at the construction site, immediately flush the inlet hopper, outlet hopper and unloading chute with the hose attached to the mixer truck, and clean the sludge and concrete adhered to the vehicle body. On the way back to the mixing plant, 150-200l water shall be injected into the mixing drum to clean the concrete residue bonded to the drum wall and blades.
2、每天工作结束后,司机应负责向搅拌筒内注入清水并高速(14—18转/分)旋转5—10分钟,然后将水排去,以保证筒内清洁。用高压水清洗搅拌筒各个部分时,应注意避开仪表及操纵杆等部位。压力水喷嘴与车身油漆表面间的距离不得小于40厘米。
2. After the mixing drum is rotated at a high speed for 18 minutes, the driver shall be responsible for the cleaning of the mixing drum, and then the water shall be discharged into the mixing drum at a high speed for 5 minutes every day. When cleaning all parts of the mixing drum with high-pressure water, pay attention to avoid instruments, control rods and other parts. The distance between the pressure water nozzle and the paint surface of the vehicle body shall not be less than 40cm.
3、清理搅拌筒内外积污及残存的混凝土渣块时,以及在机修人员进入筒内进行检修和焊补作业时,需先关闭汽车发动机,使搅拌筒完全停止转动。在机修人员进入筒内工作期间,需要保证拌筒内通风良好,空气新鲜,无可然气体及有害灰尘,氧气供应充足。在筒内使用电动工具操作时,操作人员需要有良好的绝缘保护。
3. When cleaning the dirt and residual concrete slag inside and outside the mixing drum, and when the mechanical maintenance personnel enter the drum for maintenance and welding repair, it is necessary to turn off the automobile engine first to stop the mixing drum completely. During the period when the mechanical maintenance personnel enter the drum for work, it is necessary to ensure that the mixing drum is well ventilated, the air is fresh, there is no combustible gas and harmful dust, and the oxygen supply is sufficient. When using electric tools in the cylinder, the operator needs to have good insulation protection.
4、工作时,不得将手伸入旋转的搅拌筒内,严禁将手伸入主卸料熘槽和加长卸料熘槽的连接部位自动,自动上交搅拌车在工作时应注意什么以免发生事故。
4. When working, do not put your hand into the rotating mixing drum. It is strictly prohibited to put your hand into the connecting part of the main unloading and frying tank and the extended unloading and frying tank. What should be paid attention to when working to avoid accidents.
由于混凝土会在短时间内凝固成硬块,且对钢材和油漆有一定的腐蚀性,所以每次使用混凝土贮罐后,洗净粘附在混凝土贮罐及进出料口上的混凝土是每日维护一定要认真进行的工作。其中包括:
Since the concrete will solidify into hard blocks in a short time and have certain corrosivity to steel and paint, cleaning the concrete adhered to the concrete storage tank and the inlet and outlet after each use of the concrete storage tank is a daily maintenance work that must be carried out carefully. These include:
1.每次装料前用水冲洗进料口,使进料口在装料时保持湿润;
1. Wash the inlet with water before loading each time to keep the inlet moist during loading;
2.在装料的同时向随车自带的清洗用水水箱中注满水;
2. Fill the cleaning water tank with water while loading;
3.装料后冲洗进料口,洗净进料口附近残留的混凝土;
3. After loading, wash the inlet and clean the residual concrete near the inlet;
4.到工地卸料后,冲洗出料槽,然后向混凝土贮罐内加清洗用水30—40 L;在车辆回程时保持混凝土贮罐正向慢速转动;
4. After unloading at the construction site, wash the discharge tank, and then add 30-40 l of cleaning water to the concrete storage tank; Keep the concrete storage tank in the forward direction when the vehicle rotates slowly;
5.下次装料前切记放掉混凝土贮罐内的污水;
5. Remember to drain the sewage in the concrete storage tank before the next loading;
6.每天收工时彻混凝土贮罐及进出料口周围,保证不粘有水泥及混凝土结块。
6. At the end of each day, penetrate around the concrete storage tank and the inlet and outlet to ensure that there is no cement and concrete caking.
The above is a detailed introduction to the automatic mixer, which I hope will be helpful to you If you have any questions, please contact us We will provide you with professional service http://www.shanqijituan.cn/